London North Western Railway / British Railways Lining Grey. Used in conjunction with P106 Lining Cream & P107 Lining Red.

From the about Mid 1880's until 1921 all L.N.W.R. Locomotives were lined with these colours as were all British Railways Mixed Traffic locomotives from 1948 to 1966.

All of our British Railways colours were matched to colour panels supplied to us by the Technical Services Department at Derby when we were suppliers to British Rail in the late 1970's and early 1980's.

Technical Specifications  

As supplied, a high quality synthetic (oil based) brushing enamel paint.

Stir thoroughly with a spatula (lollipop stick, wooden coffee stirer etc.) for a minimum of 5-10 minutes, or a power stirer. Ensure that you get into the bottom corners of the can and bring any sediment to the surface and stir in.

May be thined, if required, for brushing using PQ8 General Purpose Thinners.

For spraying, thin to approximately 80% paint:20% PQ9 Quick Air Drying Thinners and spray from between 75 - 100mm (3-4 inches) at a pressure of about 2 bar (30 p.s.i.).

Matt colours may require more thinning.

This product is best brushed or sprayed at a temperature of below 10° Centigrade ( 50°F). and left for a Minimum of 24 - 48 hours to dry before any overcoating or further actions are taken.

Apply over the top of a properly primed surface.

Please Note: Not all colours are available in all sizes.
Please see our disclaimer regarding colour and quantities below.

London North Western Railway / British Railways Lining Red. Used in conjunction with P105 Lining Grey & P106 Lining Cream.

From the about Mid 1880's until 1921 all L.N.W.R. Locomotives were lined with these colours as were all British Railways Mixed Traffic locomotives from 1948 to 1966.

All of our British Railways colours were matched to colour panels supplied to us by the Technical Services Department at Derby when we were suppliers to British Rail in the late 1970's and early 1980's.

Technical Specifications  

As supplied, a high quality synthetic (oil based) brushing enamel paint.

Stir thoroughly with a spatula (lollipop stick, wooden coffee stirer etc.) for a minimum of 5-10 minutes, or a power stirer. Ensure that you get into the bottom corners of the can and bring any sediment to the surface and stir in.

May be thined, if required, for brushing using PQ8 General Purpose Thinners.

For spraying, thin to approximately 80% paint:20% PQ9 Quick Air Drying Thinners and spray from between 75 - 100mm (3-4 inches) at a pressure of about 2 bar (30 p.s.i.).

Matt colours may require more thinning.

This product is best brushed or sprayed at a temperature of below 10° Centigrade ( 50°F). and left for a Minimum of 24 - 48 hours to dry before any overcoating or further actions are taken.

Apply over the top of a properly primed surface.

Please Note: Not all colours are available in all sizes.
Please see our disclaimer regarding colour and quantities below.

Black As supplied, a high quality synthetic (oil based) brushing enamel paint.

Stir thoroughly with a spatula (lollipop stick, wooden coffee stirer etc.) for a minimum of 5-10 minutes, or a power stirer. Ensure that you get into the bottom corners of the can and bring any sediment to the surface and stir in.

May be thined, if required, for brushing using PQ8 General Purpose Thinners.

For spraying, thin to approximately 80% paint:20% PQ9 Quick Air Drying Thinners and spray from between 75 - 100mm (3-4 inches) at a pressure of about 2 bar (30 p.s.i.).

Matt colours may require more thinning.

This product is best brushed or sprayed at a temperature of below 10° Centigrade ( 50°F). and left for a Minimum of 24 - 48 hours to dry before any overcoating or further actions are taken.

Apply over the top of a properly primed surface.

Please Note: Not all colours are available in all sizes.
Please see our disclaimer regarding colour and quantities below.

British Railways Signal Yellow. / Network Rail Bodyside Yellow

Used for signal arms, vehicles, brakedown trains and Warning Panels from introduction until 1985.

All of our British Railways colours were matched to colour panels supplied to us by the Technical Services Department at Derby when we were suppliers to British Rail in the late 1970's and early 1980's 

Technical Specifications 

As supplied, a high quality synthetic (oil based) brushing enamel paint.

Stir thoroughly with a spatula (lollipop stick, wooden coffee stirer etc.) for a minimum of 5-10 minutes, or a power stirer. Ensure that you get into the bottom corners of the can and bring any sediment to the surface and stir in.

May be thined, if required, for brushing using PQ8 General Purpose Thinners.

For spraying, thin to approximately 80% paint:20% PQ9 Quick Air Drying Thinners and spray from between 75 - 100mm (3-4 inches) at a pressure of about 2 bar (30 p.s.i.).

Matt colours may require more thinning.

This product is best brushed or sprayed at a temperature of below 10° Centigrade ( 50°F). and left for a Minimum of 24 - 48 hours to dry before any overcoating or further actions are taken.

Apply over the top of a properly primed surface.

This Product Contains LEAD.

Please Note: Not all colours are available in all sizes.
Please see our disclaimer regarding colour and quantities below.

Great Western Railway Signal Red as used for the buffer beams and between the frames on all Locomotives for the period between 1945 and 1948.

British Railways Signal Red. Used for signal arms, brakedown trains, buffer beams and between the frames.
 

This is the later light red used after the Second World War for ALL GWR locomotives.

This particular colour, in conjunction with P100 GWR/BR Locomotive Green and P104 Lining Orange, is the correct colour for All post war GWR and ALL BR green locomotives.

All of our British Railways colours were matched to colour panels supplied to us by the Technical Services Department at Derby when we were suppliers to British Rail in the late 1970's and early 1980's. All of our GWR colours were matched to a privately preserved set of paint panels from Swindon Works. These not only had the colours, but the dates used and the names for each colour. Our understanding is that the panels had been signed by the CME for the period.

Technical Specifications 

As supplied, a high quality synthetic (oil based) brushing enamel paint.

Stir thoroughly with a spatula (lollipop stick, wooden coffee stirer etc.) for a minimum of 5-10 minutes, or a power stirer. Ensure that you get into the bottom corners of the can and bring any sediment to the surface and stir in.

May be thined, if required, for brushing using PQ8 General Purpose Thinners.

For spraying, thin to approximately 80% paint:20% PQ9 Quick Air Drying Thinners and spray from between 75 - 100mm (3-4 inches) at a pressure of about 2 bar (30 p.s.i.).

Matt colours may require more thinning.

This product is best brushed or sprayed at a temperature of below 10° Centigrade ( 50°F). and left for a Minimum of 24 - 48 hours to dry before any overcoating or further actions are taken.

Apply over the top of a properly primed surface.

This Product Contains LEAD.

Please Note: Not all colours are available in all sizes.
Please see our disclaimer regarding colour and quantities below.