Black As supplied, a high quality synthetic (oil based) brushing enamel paint.

Stir thoroughly with a spatula (lollipop stick, wooden coffee stirer etc.) for a minimum of 5-10 minutes, or a power stirer. Ensure that you get into the bottom corners of the can and bring any sediment to the surface and stir in.

May be thined, if required, for brushing using PQ8 General Purpose Thinners.

For spraying, thin to approximately 80% paint:20% PQ9 Quick Air Drying Thinners and spray from between 75 - 100mm (3-4 inches) at a pressure of about 2 bar (30 p.s.i.).

Matt colours may require more thinning.

This product is best brushed or sprayed at a temperature of below 10° Centigrade ( 50°F). and left for a Minimum of 24 - 48 hours to dry before any overcoating or further actions are taken.

Apply over the top of a properly primed surface.

Please Note: Not all colours are available in all sizes.
Please see our disclaimer regarding colour and quantities below.

Buffer Beam Red As supplied, a high quality synthetic (oil based) brushing enamel paint.

Stir thoroughly with a spatula (lollipop stick, wooden coffee stirer etc.) for a minimum of 5-10 minutes, or a power stirer. Ensure that you get into the bottom corners of the can and bring any sediment to the surface and stir in.

May be thined, if required, for brushing using PQ8 General Purpose Thinners.

For spraying, thin to approximately 80% paint:20% PQ9 Quick Air Drying Thinners and spray from between 75 - 100mm (3-4 inches) at a pressure of about 2 bar (30 p.s.i.).

Matt colours may require more thinning.

This product is best brushed or sprayed at a temperature of below 10° Centigrade ( 50°F). and left for a Minimum of 24 - 48 hours to dry before any overcoating or further actions are taken.

Apply over the top of a properly primed surface.

Please Note: Not all colours are available in all sizes.
Please see our disclaimer regarding colour and quantities below.

Coach Teak. Wood was the standard method of coach body construction for both the GNR and LNER as well as a number of other railways.

This paint is best applied over light base coat (P16, P995, P117, P133, P21 have all been used to good effect).

Dry brush the teak paint over the base coat in the direction of the grain, horizontal for the upper panels and vertical for the lower panels.

The colour of the base coat will help to determine the colour of the finished teak.

Apply transfers and then carefully apply a coat of varnish over the whole coach.

Unless two coaches were finished at the same time they will be different colours.

See our page on painting Teak Coaches for more details.

Technical Specifications  

As supplied, a high quality synthetic (oil based) brushing enamel paint.

Stir thoroughly with a spatula (lollipop stick, wooden coffee stirer etc.) for a minimum of 5-10 minutes, or a power stirer. Ensure that you get into the bottom corners of the can and bring any sediment to the surface and stir in.

May be thined, if required, for brushing using PQ8 General Purpose Thinners.

For spraying, thin to approximately 80% paint:20% PQ9 Quick Air Drying Thinners and spray from between 75 - 100mm (3-4 inches) at a pressure of about 2 bar (30 p.s.i.).

Matt colours may require more thinning.

This product is best brushed or sprayed at a temperature of below 10° Centigrade ( 50°F). and left for a Minimum of 24 - 48 hours to dry before any overcoating or further actions are taken.

Apply over the top of a properly primed surface.

This Product Contains LEAD.

Please Note: Not all colours are available in all sizes.
Please see our disclaimer regarding colour and quantities below.

London & North Eastern Railway Locomotive Green (Darlington Shade). This is the shade adopted by Darlington works. It is believed that this shade is as close to the old North Eastern Railway green that Darlington could get without upsetting Gresley too much.

LNER Green locomotives were lined with a white/black/white configuration.

Technical Specifications  

As supplied, a high quality synthetic (oil based) brushing enamel paint.

Stir thoroughly with a spatula (lollipop stick, wooden coffee stirer etc.) for a minimum of 5-10 minutes, or a power stirer. Ensure that you get into the bottom corners of the can and bring any sediment to the surface and stir in.

May be thined, if required, for brushing using PQ8 General Purpose Thinners.

For spraying, thin to approximately 80% paint:20% PQ9 Quick Air Drying Thinners and spray from between 75 - 100mm (3-4 inches) at a pressure of about 2 bar (30 p.s.i.).

Matt colours may require more thinning.

This product is best brushed or sprayed at a temperature of below 10° Centigrade ( 50°F). and left for a Minimum of 24 - 48 hours to dry before any overcoating or further actions are taken.

Apply over the top of a properly primed surface.

Please Note: Not all colours are available in all sizes.
Please see our disclaimer regarding colour and quantities below.

Roof Grey for L.N.E.R. Coaches. For white roofs use either Matt White (P976 matt) for ex works coaches or P24 GWR Roof White for a coach a few days out of works.

Technical Specifications 

As supplied, a high quality synthetic (oil based) brushing enamel paint.

Stir thoroughly with a spatula (lollipop stick, wooden coffee stirer etc.) for a minimum of 5-10 minutes, or a power stirer. Ensure that you get into the bottom corners of the can and bring any sediment to the surface and stir in.

May be thined, if required, for brushing using PQ8 General Purpose Thinners.

For spraying, thin to approximately 80% paint:20% PQ9 Quick Air Drying Thinners and spray from between 75 - 100mm (3-4 inches) at a pressure of about 2 bar (30 p.s.i.).

Matt colours may require more thinning.

This product is best brushed or sprayed at a temperature of below 10° Centigrade ( 50°F). and left for a Minimum of 24 - 48 hours to dry before any overcoating or further actions are taken.

Apply over the top of a properly primed surface.

Please Note: Not all colours are available in all sizes.
Please see our disclaimer regarding colour and quantities below.

LNER A4 Class  4-6-2 locomotive "HERRING GULL" Nameplates

Colour: As per choosen option

Quantity: One Set (2 nameplates)

Technical Specifications 

High Quality Name and Smokebox Numberplates.
Nameplates are produced on 0.008" brass and are supplied painted and coated with an Anti Tarnish Coating.
Smokebox Numberplates are produced in 0.005" Stainless Steel and are supplied painted.
All Name and Numberplates have been produced from photographic evidence to ensure that not only is the font correct but also the alignment and spacing of the letters.
Eastern Region 'curly sixes' - where there is photographic evidence that a particular locomotive carried a smokebox plate, even if for only a short time, with a 'curly 6' then it will be included in the set.

Please Note: Not all colours are available in all sizes.

Please see our disclaimer regarding colour and quantities below.